A U of T Engineering innovation could make printing cells as easy and inexpensive as printing a newspaper. Dr. Hairen Tan and his team have cleared a critical manufacturing hurdle in the development of a relatively new class of solar devices called perovskite solar cells. This alternative solar technology could lead to low-cost, printable solar panels capable of turning nearly any surface into a power generator.
“Economies of scale have greatly reduced the cost of silicon manufacturing,” says University Professor Ted Sargent (ECE), an expert in emerging solar technologies and the Canada Research Chair in Nanotechnology and senior author on the paper. “Perovskite solar cells can enable us to use techniques already established in the printing industry to produce solar cells at very low cost. Potentially, perovskites and silicon cells can be married to improve efficiency further, but only with advances in low-temperature processes.”
Today, virtually all commercial solar cells are made from thin slices of crystalline silicon which must be processed to a very high purity. It’s an energy-intensive process, requiring temperatures higher than 1,000 degrees Celsius and large amounts of hazardous solvents.
In contrast, perovskite solar cells depend on a layer of tiny crystals — each about 1,000 times smaller than the width of a human hair — made of low-cost, light-sensitive materials. Because the perovskite raw materials can be mixed into a liquid to form a kind of ‘solar ink’, they could be printed onto glass, plastic or other materials using a simple inkjet process.
But, until now, there’s been a catch: in order to generate electricity, electrons excited by solar energy must be extracted from the crystals so they can flow through a circuit. That extraction happens in a special layer called the electron-selective layer, or ESL. The difficulty of manufacturing a good ESL has been one of the key challenges holding back the development of perovskite solar cell devices.
“The most effective materials for making ESLs start as a powder and have to be baked at high temperatures, above 500 degrees Celsius,” says Tan. “You can’t put that on top of a sheet of flexible plastic or on a fully fabricated silicon cell — it will just melt.”
Tan and his colleagues developed a new chemical reaction than enables them to grow an ESL made of nanoparticles in solution, directly on top of the electrode. While heat is still required, the process always stays below 150 degrees C, much lower than the melting point of many plastics.
The new nanoparticles are coated with a layer of chlorine atoms, which helps them bind to the perovskite layer on top — this strong binding allows for efficient extraction of electrons. In a paper recently published in Science, Tan and his colleagues report the efficiency of solar cells made using the new method at 20.1 per cent.
“This is the best ever reported for low-temperature processing techniques,” says Tan. He adds that perovskite solar cells using the older, high-temperature method are only marginally better at 22.1 per cent, and even the best silicon solar cells can only reach 26.3 per cent.
Another advantage is stability. Many perovskite solar cells experience a severe drop in performance after only a few hours, but Tan’s cells retained more than 90 per cent of their efficiency even after 500 hours of use. “I think our new technique paves the way toward solving this problem,” says Tan, who undertook this work as part of a Rubicon Fellowship.
“The Toronto team’s computational studies beautifully explain the role of the newly developed electron-selective layer. The work illustrates the rapidly-advancing contribution that computational materials science is making towards rational, next-generation energy devices,” said Professor Alán Aspuru-Guzik, an expert on computational materials science in the Department of Chemistry and Chemical Biology at Harvard University, who was not involved in the work.
“To augment the best silicon solar cells, next-generation thin-film technologies need to be process-compatible with a finished cell. This entails modest processing temperatures such as those in the Toronto group’s advance reported in Science,” said Professor Luping Yu of the University of Chicago’s Department of Chemistry. Yu is an expert on solution-processed solar cells and was not involved in the work.
Keeping cool during the manufacturing process opens up a world of possibilities for applications of perovskite solar cells, from smartphone covers that provide charging capabilities to solar-active tinted windows that offset building energy use. In the nearer term, Tan says his technology could be used in tandem with conventional solar cells.
“With our low-temperature process, we could coat our perovskite cells directly on top of silicon without damaging the underlying material,” says Tan. “If a hybrid perovskite-silicon cell can push the efficiency up to 30 per cent or higher, it makes solar power a much better economic proposition.”
Learn more: Printable solar cells just got a little closer
Receive an email update when we add a new SOLAR CELLS article.
The Latest on: Solar cells
via Google News
The Latest on: Solar cells
- Researchers think small to make progress towards better fuel cellson September 16, 2019 at 6:16 am
As renewable sources such as wind and solar are quickly changing the energy landscape, scientists are looking for ways to better store energy for when it's needed. Fuel cells, which convert ...
- Visiongain Publishes Global Fuel Cell Market 2019-2029 Reporton September 16, 2019 at 6:06 am
Fuel Cells can easily be coupled with other energy technologies, such as batteries, wind turbines, and solar panels, and can be used to power cell phones, cars and even houses. Market Overview and ...
- Ikea owner investing in solar in Texas, Utahon September 16, 2019 at 6:04 am
The Ingka Group said the investments are the first off-site solar plants for the company and will consist of 823,000 panels in Texas that are expected to come into operation in January and another 636 ...
- Radiative Sky Cooling Could Be the Night Equivalent of Solaron September 16, 2019 at 6:03 am
The team generated 25 milliwatts per square meter, which could power a single LED light bulb. That's less than a single solar cell, but the two need not work in opposition. Solar panels work best ...
- Scientists create 'reverse solar cell' that generates electrical light from darknesson September 16, 2019 at 5:25 am
Scientists have created a "reverse solar cell" that can harness the heat radiated by the Earth at night to create electrical light. Most solar panels generate electricity from the sun through a ...
- Carbon Nanotubes Might Be the Boost Solar Energy Has Been Looking Foron September 16, 2019 at 4:21 am
Elements is more than just a science show. It’s your science-loving best friend, tasked with keeping you updated and interested on all the compelling, innovative and groundbreaking science happening ...
- Chicago Company Plans 1,800-Acre Indiana Solar Farmon September 16, 2019 at 4:00 am
The proposal calls for nearly 580,000 solar panels on what is mostly farmland near the Sullivan County community of Fairbanks, some 20 miles south of Terre Haute. The company says it has long-term ...
- Welcome indoors, solar cellson September 16, 2019 at 3:40 am
(Nanowerk News) Swedish and Chinese scientists have developed organic solar cells optimised to convert ambient indoor light to electricity. The power they produce is low, but is probably enough to ...
- Flexible solar cells a step closer to reality | IDTechEx Research Articleon September 13, 2019 at 8:10 pm
Solar cells that use mixtures of organic molecules to absorb sunlight and convert it to electricity, that can be applied to curved surfaces such as the body of a car, could be a step closer thanks to ...
via Bing News